DGND3700v1 TTL日志：刷机失败，修复成功

1. 
   
2. 
   
3. D%G
   
4. 
   
5. DGND3700 Boot Code V1.0.8
   
6. CFE version 1.0.37-104.4 for BCM96368 (32bit,SP,BE)
   
7. Build Date: Mon Feb 21 17:59:46 CST 2011 (finerain@moonlight)
   
8. Copyright (C) 2000-2009 Broadcom Corporation.
   
9. 
   
10. Parallel flash device: name AM29LV320MT, id 0x2201 size 32768KB
    
11. Total Flash size: 32768K with 256 sectors
    
12. ethsw: found bcm53115!
    
13. Chip ID: BCM6368B2, MIPS: 400MHz
    
14. Main Thread: TP0
    
15. Total Memory: 134217728 bytes (128MB)
    
16. Boot Address: 0xb8000000
    
17. 
    
18. Board IP address                  : 192.168.1.1:ffffff00  
    
19. Host IP address                   : 192.168.1.100  
    
20. Gateway IP address                :   
    
21. Run from flash/host (f/h)         : f  
    
22. Default host run file name        : vmlinux  
    
23. Default host flash file name      : bcm963xx_fs_kernel  
    
24. Boot delay (0-9 seconds)          : 1  
    
25. Board Id (0-11)                   : 96368MVWG  
    
26. Number of MAC Addresses (1-32)    : 10  
    
27. Base MAC Address                  : 20:4e:7f:0f:89:ce  
    
28. PSI Size (1-64) KBytes            : 24  
    
29. Enable Backup PSI [0|1]           : 0  
    
30. System Log Size (0-256) KBytes    : 0  
    
31. Main Thread Number [0|1]          : 0  
    
32. 
    
33. *** Press any key to stop auto run (1 seconds) ***
    
34. Auto run second count down: 110
    
35. Booting from only image (0xb8020000) ...
    
36. Code Address: 0x80010000, Entry Address: 0x80298000
    
37. Decompression OK!
    
38. Entry at 0x80298000
    
39. Closing network.
    
40. Disabling Switch ports.
    
41. Flushing Receive Buffers...
    
42. 61 buffers found.
    
43. Closing DMA Channels.
    
44. Starting program at 0x80298000
    
45. Linux version 2.6.21.5 (nop@localhost.localdomain) (gcc version 4.2.3) #1 Mon Sep 22 18:21:11 CST 2014
    
46. 
    
47. Parallel flash device: name AM29LV320MT, id 0x2201 size 32768KB
    
48. 
    
49. 96368MVWG prom init
    
50. 
    
51. CPU revision is: 0002a031
    
52. 
    
53. Determined physical RAM map:
    
54. 
    
55. memory: 07f00000 @ 00000000 (usable)
    
56. 
    
57. On node 0 totalpages: 32512
    
58. 
    
59.   DMA zone: 32 pages used for memmap
    
60. 
    
61.   DMA zone: 0 pages reserved
    
62. 
    
63.   DMA zone: 4064 pages, LIFO batch:0
    
64. 
    
65.   Normal zone: 222 pages used for memmap
    
66. 
    
67.   Normal zone: 28194 pages, LIFO batch:7
    
68. 
    
69. Built 1 zonelists.  Total pages: 32258
    
70. 
    
71. Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
    
72. 
    
73. brcm mips: enabling icache and dcache...
    
74. 
    
75. Primary instruction cache 64kB, physically tagged, 4-way, linesize 16 bytes.
    
76. 
    
77. Primary data cache 32kB, 2-way, linesize 16 bytes.
    
78. 
    
79. Synthesized TLB refill handler (21 instructions).
    
80. 
    
81. Synthesized TLB load handler fastpath (33 instructions).
    
82. 
    
83. Synthesized TLB store handler fastpath (33 instructions).
    
84. 
    
85. Synthesized TLB modify handler fastpath (32 instructions).
    
86. 
    
87. PID hash table entries: 512 (order: 9, 2048 bytes)
    
88. 
    
89. Using 200.000 MHz high precision timer.
    
90. 
    
91. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
    
92. 
    
93. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
    
94. 
    
95. Memory: 126012k/130048k available (2097k kernel code, 4012k reserved, 490k data, 92k init, 0k highmem)
    
96. 
    
97. KLOB Pool 1 Initialized: 1048576 bytes <0x80300000 ... 0x80400000>
    
98. 
    
99. Calibrating delay loop... 398.95 BogoMIPS (lpj=997376)
    
100. 
     
101. Mount-cache hash table entries: 512
     
102. 
     
103. wait instruction: enabled
     
104. 
     
105. NET: Registered protocol family 16
     
106. 
     
107. Total Flash size: 32768K with 256 sectors
     
108. 
     
109. registering PCI controller with io_map_base unset
     
110. 
     
111. SCSI subsystem initialized
     
112. 
     
113. usbcore: registered new interface driver usbfs
     
114. 
     
115. usbcore: registered new interface driver hub
     
116. 
     
117. usbcore: registered new device driver usb
     
118. 
     
119. BLOG v2.1 Initialized
     
120. 
     
121. NET: Registered protocol family 8
     
122. 
     
123. NET: Registered protocol family 20
     
124. 
     
125. Time: MIPS clocksource has been installed.
     
126. 
     
127. NET: Registered protocol family 2
     
128. 
     
129. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
     
130. 
     
131. TCP established hash table entries: 4096 (order: 3, 32768 bytes)
     
132. 
     
133. TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
     
134. 
     
135. TCP: Hash tables configured (established 4096 bind 4096)
     
136. 
     
137. TCP reno registered
     
138. 
     
139. squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
     
140. 
     
141. squashfs: LZMA suppport for slax.org by jro
     
142. 
     
143. JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
     
144. 
     
145. fuse init (API version 7.8)
     
146. 
     
147. io scheduler noop registered (default)
     
148. 
     
149. PPP generic driver version 2.4.2
     
150. 
     
151. NET: Registered protocol family 24
     
152. 
     
153. physmap platform flash device: 02000000 at b8000000
     
154. 
     
155. physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
     
156. 
     
157. Amd/Fujitsu Extended Query Table at 0x0040
     
158. 
     
159. physmap-flash.0: CFI does not contain boot bank location. Assuming top.
     
160. 
     
161. number of CFI chips: 1
     
162. 
     
163. cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
     
164. 
     
165. cmdlinepart partition parsing not available
     
166. 
     
167. RedBoot partition parsing not available
     
168. 
     
169. Using physmap partition information
     
170. 
     
171. Creating 17 MTD partitions on "physmap-flash.0":
     
172. 
     
173. 0x00020100-0x01e40000 : "rootfs"
     
174. 
     
175. mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
     
176. 
     
177. 0x00020000-0x01e40000 : "fw_upgrade"
     
178. 
     
179. 0x01e40000-0x01e60000 : "SP"
     
180. 
     
181. 0x01e60000-0x01e80000 : "MISC"
     
182. 
     
183. 0x01e80000-0x01ea0000 : "DPF"
     
184. 
     
185. 0x01ea0000-0x01ec0000 : "T_Meter1"
     
186. 
     
187. 0x01ec0000-0x01ee0000 : "T_Meter2"
     
188. 
     
189. 0x01ee0000-0x01f00000 : "T_Meter3"
     
190. 
     
191. 0x01f00000-0x01f20000 : "T_Meter4"
     
192. 
     
193. 0x01f20000-0x01f40000 : "POT"
     
194. 
     
195. 0x01f40000-0x01f60000 : "Reserved1"
     
196. 
     
197. 0x01f60000-0x01f80000 : "Reserved2"
     
198. 
     
199. 0x01f80000-0x01fa0000 : "Reserved3"
     
200. 
     
201. 0x01fa0000-0x01fc0000 : "Reserved4"
     
202. 
     
203. 0x01fc0000-0x01fe0000 : "board_data"
     
204. 
     
205. 0x01fe0000-0x02000000 : "nvram"
     
206. 
     
207. 0x00000000-0x02000000 : "whole_flash"
     
208. 
     
209. bcm963xx_mtd driver v1.0
     
210. 
     
211. File system address: 0xb8020100
     
212. 
     
213. Broadcom DSL NAND controller (BrcmNand Controller)
     
214. 
     
215. i=0, CS[0] = 0
     
216. 
     
217. brcmnand_probe: CS0: dev_id=ecf10095
     
218. 
     
219. NAND Config: Reg=55042200, chipSize=128 MB, blockSize=128K, erase_shift=11
     
220. 
     
221. busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
     
222. 
     
223. timing1 not adjusted: 5363444f
     
224. 
     
225. timing2 not adjusted: 00000fc6
     
226. 
     
227. BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB
     
228. 
     
229. 
     
230. Found NAND: ACC=d3000000, cfg=55042200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6
     
231. 
     
232. BrcmNAND version = 0x0201 128MB @00000000
     
233. 
     
234. brcmnand_probe: CS0: dev_id=ecf10095
     
235. 
     
236. 1. Found NAND chip on Chip Select 0, chipSize=128MB, usable size=128MB, base=0x00000000
     
237. 
     
238. brcmnand_scan: B4 nand_select = 40000002
     
239. 
     
240. brcmnand_scan: After nand_select = 40000002
     
241. 
     
242. page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
     
243. 
     
244. Brcm NAND controller version = 2.1 NAND flash size 128MB @16000000
     
245. 
     
246. brcmnand_scan:  mtd->oobsize=64
     
247. 
     
248. brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
     
249. 
     
250. brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
     
251. 
     
252. brcmnand_default_bbt: bbt_td = bbt_main_descr
     
253. 
     
254. Bad block table found at page 65472, version 0xFF
     
255. 
     
256. Bad block table found at page 65408, version 0xFF
     
257. 
     
258.     numchips=1, size=8000000
     
259. 
     
260. Creating 1 MTD partitions on "bcm63xx-nand.0":
     
261. 
     
262. 0x00000000-0x08000000 : "storage"
     
263. 
     
264. PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
     
265. 
     
266. PCI: Setting latency timer of device 0000:00:0a.0 to 64
     
267. 
     
268. ehci_hcd 0000:00:0a.0: EHCI Host Controller
     
269. 
     
270. ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
     
271. 
     
272. ehci_hcd 0000:00:0a.0: irq 15, io mem 0x10001500
     
273. 
     
274. ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00, driver 10 Dec 2004
     
275. 
     
276. usb usb1: configuration #1 chosen from 1 choice
     
277. 
     
278. hub 1-0:1.0: USB hub found
     
279. 
     
280. hub 1-0:1.0: 2 ports detected
     
281. 
     
282. ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
     
283. 
     
284. PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
     
285. 
     
286. PCI: Setting latency timer of device 0000:00:09.0 to 64
     
287. 
     
288. ohci_hcd 0000:00:09.0: OHCI Host Controller
     
289. 
     
290. ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
     
291. 
     
292. ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600
     
293. 
     
294. usb usb2: configuration #1 chosen from 1 choice
     
295. 
     
296. hub 2-0:1.0: USB hub found
     
297. 
     
298. hub 2-0:1.0: 2 ports detected
     
299. 
     
300. usbcore: registered new interface driver usblp
     
301. 
     
302. drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
     
303. 
     
304. Initializing USB Mass Storage driver...
     
305. 
     
306. usbcore: registered new interface driver usb-storage
     
307. 
     
308. USB Mass Storage support registered.
     
309. 
     
310. brcmboard: brcm_board_init entry
     
311. 
     
312. 
     
313. ===>brcm_board_init: GPIO->GPIOBaseMode=0x3b000
     
314. 
     
315. 
     
316. ===>brcm_board_init: GPIO->GPIOMode=0x1f0003
     
317. 
     
318. Serial: BCM63XX driver $Revision: 3.00 $
     
319. 
     
320. ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX
     
321. 
     
322. ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX
     
323. 
     
324. bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Sep 22 2014 18:20:11
     
325. 
     
326. netem: version 1.2
     
327. 
     
328. u32 classifier
     
329. 
     
330. TCP cubic registered
     
331. 
     
332. NET: Registered protocol family 1
     
333. 
     
334. NET: Registered protocol family 17
     
335. 
     
336. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
     
337. 
     
338. All bugs added by David S. Miller <davem@redhat.com>
     
339. 
     
340. VFS: Mounted root (squashfs filesystem) readonly.
     
341. 
     
342. Freeing unused kernel memory: 92k freed
     
343. 
     
344. Warning: unable to open an initial console.
     
345. D%G
     
346. 
     
347. DGND3700 Boot Code V1.0.8
     
348. CFE version 1.0.37-104.4 for BCM96368 (32bit,SP,BE)
     
349. Build Date: Mon Feb 21 17:59:46 CST 2011 (finerain@moonlight)
     
350. Copyright (C) 2000-2009 Broadcom Corporation.
     
351. 
     
352. Parallel flash device: name AM29LV320MT, id 0x2201 size 32768KB
     
353. Total Flash size: 32768K with 256 sectors
     
354. ethsw: found bcm53115!
     
355. Chip ID: BCM6368B2, MIPS: 400MHz
     
356. Main Thread: TP0
     
357. Total Memory: 134217728 bytes (128MB)
     
358. Boot Address: 0xb8000000
     
359. 
     
360. Board IP address                  : 192.168.1.1:ffffff00  
     
361. Host IP address                   : 192.168.1.100  
     
362. Gateway IP address                :   
     
363. Run from flash/host (f/h)         : f  
     
364. Default host run file name        : vmlinux  
     
365. Default host flash file name      : bcm963xx_fs_kernel  
     
366. Boot delay (0-9 seconds)          : 1  
     
367. Board Id (0-11)                   : 96368MVWG  
     
368. Number of MAC Addresses (1-32)    : 10  
     
369. Base MAC Address                  : 20:4e:7f:0f:89:ce  
     
370. PSI Size (1-64) KBytes            : 24  
     
371. Enable Backup PSI [0|1]           : 0  
     
372. System Log Size (0-256) KBytes    : 0  
     
373. Main Thread Number [0|1]          : 0  
     
374. 
     
375. *** Press any key to stop auto run (1 seconds) ***
     
376. Auto run second count down: 111
     
377. CFE> ^C
     
378. CFE>
     
379. CFE> ^C
     
380. CFE>
     
381. CFE> ^C
     
382. CFE> tftpd
     
383. Start TFTP server
     
384. Loading : ...
     
385. Finished loading 8234291 bytes
     
386. Loading .............................................................................................
     
387. ...............................................................
     
388. 
     
389. 
     
390. Resetting board...
     
391. 
     
392. DGND3700 Boot Code V1.0.8
     
393. CFE version 1.0.37-104.4 for BCM96368 (32bit,SP,BE)
     
394. Build Date: Mon Feb 21 17:59:46 CST 2011 (finerain@moonlight)
     
395. Copyright (C) 2000-2009 Broadcom Corporation.
     
396. 
     
397. Parallel flash device: name AM29LV320MT, id 0x2201 size 32768KB
     
398. Total Flash size: 32768K with 256 sectors
     
399. ethsw: found bcm53115!
     
400. Chip ID: BCM6368B2, MIPS: 400MHz
     
401. Main Thread: TP0
     
402. Total Memory: 134217728 bytes (128MB)
     
403. Boot Address: 0xb8000000
     
404. 
     
405. Board IP address                  : 192.168.1.1:ffffff00  
     
406. Host IP address                   : 192.168.1.100  
     
407. Gateway IP address                :   
     
408. Run from flash/host (f/h)         : f  
     
409. Default host run file name        : vmlinux  
     
410. Default host flash file name      : bcm963xx_fs_kernel  
     
411. Boot delay (0-9 seconds)          : 1  
     
412. Board Id (0-11)                   : 96368MVWG  
     
413. Number of MAC Addresses (1-32)    : 10  
     
414. Base MAC Address                  : 20:4e:7f:0f:89:ce  
     
415. PSI Size (1-64) KBytes            : 24  
     
416. Enable Backup PSI [0|1]           : 0  
     
417. System Log Size (0-256) KBytes    : 0  
     
418. Main Thread Number [0|1]          : 0  
     
419. 
     
420. *** Press any key to stop auto run (1 seconds) ***
     
421. Auto run second count down: 110
     
422. Booting from only image (0xb8020000) ...
     
423. Code Address: 0x80010000, Entry Address: 0x80298000
     
424. Decompression OK!
     
425. Entry at 0x80298000
     
426. Closing network.
     
427. Disabling Switch ports.
     
428. Flushing Receive Buffers...
     
429. 59 buffers found.
     
430. Closing DMA Channels.
     
431. Starting program at 0x80298000
     
432. Linux version 2.6.21.5 (finerain@sunshine) (gcc version 4.2.3) #1 Fri Oct 21 08:04:47 CST 2011
     
433. 
     
434. Parallel flash device: name AM29LV320MT, id 0x2201 size 32768KB
     
435. 
     
436. 96368MVWG prom init
     
437. 
     
438. CPU revision is: 0002a031
     
439. 
     
440. Determined physical RAM map:
     
441. 
     
442. memory: 07f00000 @ 00000000 (usable)
     
443. 
     
444. On node 0 totalpages: 32512
     
445. 
     
446.   DMA zone: 32 pages used for memmap
     
447. 
     
448.   DMA zone: 0 pages reserved
     
449. 
     
450.   DMA zone: 4064 pages, LIFO batch:0
     
451. 
     
452.   Normal zone: 222 pages used for memmap
     
453. 
     
454.   Normal zone: 28194 pages, LIFO batch:7
     
455. 
     
456. Built 1 zonelists.  Total pages: 32258
     
457. 
     
458. Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
     
459. 
     
460. brcm mips: enabling icache and dcache...
     
461. 
     
462. Primary instruction cache 64kB, physically tagged, 4-way, linesize 16 bytes.
     
463. 
     
464. Primary data cache 32kB, 2-way, linesize 16 bytes.
     
465. 
     
466. Synthesized TLB refill handler (21 instructions).
     
467. 
     
468. Synthesized TLB load handler fastpath (33 instructions).
     
469. 
     
470. Synthesized TLB store handler fastpath (33 instructions).
     
471. 
     
472. Synthesized TLB modify handler fastpath (32 instructions).
     
473. 
     
474. PID hash table entries: 512 (order: 9, 2048 bytes)
     
475. 
     
476. Using 200.000 MHz high precision timer.
     
477. 
     
478. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
     
479. 
     
480. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
     
481. 
     
482. Memory: 126012k/130048k available (2097k kernel code, 4012k reserved, 490k data, 92k init, 0k highmem)
     
483. 
     
484. KLOB Pool 1 Initialized: 1048576 bytes <0x80300000 ... 0x80400000>
     
485. 
     
486. Calibrating delay loop... 398.95 BogoMIPS (lpj=997376)
     
487. 
     
488. Mount-cache hash table entries: 512
     
489. 
     
490. wait instruction: enabled
     
491. 
     
492. NET: Registered protocol family 16
     
493. 
     
494. Total Flash size: 32768K with 256 sectors
     
495. 
     
496. registering PCI controller with io_map_base unset
     
497. 
     
498. SCSI subsystem initialized
     
499. 
     
500. usbcore: registered new interface driver usbfs
     
501. 
     
502. usbcore: registered new interface driver hub
     
503. 
     
504. usbcore: registered new device driver usb
     
505. 
     
506. BLOG v2.1 Initialized
     
507. 
     
508. NET: Registered protocol family 8
     
509. 
     
510. NET: Registered protocol family 20
     
511. 
     
512. Time: MIPS clocksource has been installed.
     
513. 
     
514. NET: Registered protocol family 2
     
515. 
     
516. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
     
517. 
     
518. TCP established hash table entries: 4096 (order: 3, 32768 bytes)
     
519. 
     
520. TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
     
521. 
     
522. TCP: Hash tables configured (established 4096 bind 4096)
     
523. 
     
524. TCP reno registered
     
525. 
     
526. squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
     
527. 
     
528. squashfs: LZMA suppport for slax.org by jro
     
529. 
     
530. JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
     
531. 
     
532. fuse init (API version 7.8)
     
533. 
     
534. io scheduler noop registered (default)
     
535. 
     
536. PPP generic driver version 2.4.2
     
537. 
     
538. NET: Registered protocol family 24
     
539. 
     
540. physmap platform flash device: 02000000 at b8000000
     
541. 
     
542. physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
     
543. 
     
544. Amd/Fujitsu Extended Query Table at 0x0040
     
545. 
     
546. physmap-flash.0: CFI does not contain boot bank location. Assuming top.
     
547. 
     
548. number of CFI chips: 1
     
549. 
     
550. cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
     
551. 
     
552. cmdlinepart partition parsing not available
     
553. 
     
554. RedBoot partition parsing not available
     
555. 
     
556. Using physmap partition information
     
557. 
     
558. Creating 17 MTD partitions on "physmap-flash.0":
     
559. 
     
560. 0x00020100-0x01e40000 : "rootfs"
     
561. 
     
562. mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only
     
563. 
     
564. 0x00020000-0x01e40000 : "fw_upgrade"
     
565. 
     
566. 0x01e40000-0x01e60000 : "SP"
     
567. 
     
568. 0x01e60000-0x01e80000 : "MISC"
     
569. 
     
570. 0x01e80000-0x01ea0000 : "DPF"
     
571. 
     
572. 0x01ea0000-0x01ec0000 : "T_Meter1"
     
573. 
     
574. 0x01ec0000-0x01ee0000 : "T_Meter2"
     
575. 
     
576. 0x01ee0000-0x01f00000 : "T_Meter3"
     
577. 
     
578. 0x01f00000-0x01f20000 : "T_Meter4"
     
579. 
     
580. 0x01f20000-0x01f40000 : "POT"
     
581. 
     
582. 0x01f40000-0x01f60000 : "Reserved1"
     
583. 
     
584. 0x01f60000-0x01f80000 : "Reserved2"
     
585. 
     
586. 0x01f80000-0x01fa0000 : "Reserved3"
     
587. 
     
588. 0x01fa0000-0x01fc0000 : "Reserved4"
     
589. 
     
590. 0x01fc0000-0x01fe0000 : "board_data"
     
591. 
     
592. 0x01fe0000-0x02000000 : "nvram"
     
593. 
     
594. 0x00000000-0x02000000 : "whole_flash"
     
595. 
     
596. bcm963xx_mtd driver v1.0
     
597. 
     
598. File system address: 0xb8020100
     
599. 
     
600. Broadcom DSL NAND controller (BrcmNand Controller)
     
601. 
     
602. i=0, CS[0] = 0
     
603. 
     
604. brcmnand_probe: CS0: dev_id=ecf10095
     
605. 
     
606. NAND Config: Reg=55042200, chipSize=128 MB, blockSize=128K, erase_shift=11
     
607. 
     
608. busWidth=1, pageSize=2048B, page_shift=11, page_mask=000007ff
     
609. 
     
610. timing1 not adjusted: 5363444f
     
611. 
     
612. timing2 not adjusted: 00000fc6
     
613. 
     
614. BrcmNAND mfg ec f1 Samsung K9F1G08U0A 128MB
     
615. 
     
616. 
     
617. Found NAND: ACC=d3000000, cfg=55042200, flashId=ecf10095, tim1=5363444f, tim2=00000fc6
     
618. 
     
619. BrcmNAND version = 0x0201 128MB @00000000
     
620. 
     
621. brcmnand_probe: CS0: dev_id=ecf10095
     
622. 
     
623. 1. Found NAND chip on Chip Select 0, chipSize=128MB, usable size=128MB, base=0x00000000
     
624. 
     
625. brcmnand_scan: B4 nand_select = 40000002
     
626. 
     
627. brcmnand_scan: After nand_select = 40000002
     
628. 
     
629. page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
     
630. 
     
631. Brcm NAND controller version = 2.1 NAND flash size 128MB @16000000
     
632. 
     
633. brcmnand_scan:  mtd->oobsize=64
     
634. 
     
635. brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
     
636. 
     
637. brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
     
638. 
     
639. brcmnand_default_bbt: bbt_td = bbt_main_descr
     
640. 
     
641. Bad block table found at page 65472, version 0xFF
     
642. 
     
643. Bad block table found at page 65408, version 0xFF
     
644. 
     
645.     numchips=1, size=8000000
     
646. 
     
647. Creating 1 MTD partitions on "bcm63xx-nand.0":
     
648. 
     
649. 0x00000000-0x08000000 : "storage"
     
650. 
     
651. PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
     
652. 
     
653. PCI: Setting latency timer of device 0000:00:0a.0 to 64
     
654. 
     
655. ehci_hcd 0000:00:0a.0: EHCI Host Controller
     
656. 
     
657. ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
     
658. 
     
659. ehci_hcd 0000:00:0a.0: irq 15, io mem 0x10001500
     
660. 
     
661. ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00, driver 10 Dec 2004
     
662. 
     
663. usb usb1: configuration #1 chosen from 1 choice
     
664. 
     
665. hub 1-0:1.0: USB hub found
     
666. 
     
667. hub 1-0:1.0: 2 ports detected
     
668. 
     
669. ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
     
670. 
     
671. PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
     
672. 
     
673. PCI: Setting latency timer of device 0000:00:09.0 to 64
     
674. 
     
675. ohci_hcd 0000:00:09.0: OHCI Host Controller
     
676. 
     
677. ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
     
678. 
     
679. ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600
     
680. 
     
681. usb usb2: configuration #1 chosen from 1 choice
     
682. 
     
683. hub 2-0:1.0: USB hub found
     
684. 
     
685. hub 2-0:1.0: 2 ports detected
     
686. 
     
687. usbcore: registered new interface driver usblp
     
688. 
     
689. drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
     
690. 
     
691. Initializing USB Mass Storage driver...
     
692. 
     
693. usbcore: registered new interface driver usb-storage
     
694. 
     
695. USB Mass Storage support registered.
     
696. 
     
697. brcmboard: brcm_board_init entry
     
698. 
     
699. 
     
700. ===>brcm_board_init: GPIO->GPIOBaseMode=0x3b000
     
701. 
     
702. 
     
703. ===>brcm_board_init: GPIO->GPIOMode=0x1f0003
     
704. 
     
705. Serial: BCM63XX driver $Revision: 3.00 $
     
706. 
     
707. ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX
     
708. 
     
709. ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX
     
710. 
     
711. bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Oct 21 2011 08:03:27
     
712. 
     
713. netem: version 1.2
     
714. 
     
715. u32 classifier
     
716. 
     
717. TCP cubic registered
     
718. 
     
719. NET: Registered protocol family 1
     
720. 
     
721. NET: Registered protocol family 17
     
722. 
     
723. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
     
724. 
     
725. All bugs added by David S. Miller <davem@redhat.com>
     
726. 
     
727. VFS: Mounted root (squashfs filesystem) readonly.
     
728. 
     
729. Freeing unused kernel memory: 92k freed
     
730. 
     
731. 
     
732. init started:  BusyBox v1.00 (2011.10.21-00:18+0000) multi-call binary
     
733. 
     
734. 
     
735. BusyBox v1.00 (2011.10.21-00:18+0000) Built-in shell (ash)
     
736. Enter 'help' for a list of built-in commands.
     
737. 
     
738. 
     
739. Loading drivers and kernel modules...
     
740. 
     
741. pktflow: module license 'Proprietary' taints kernel.
     
742. 
     
743. Broadcom Packet Flow Cache  Char Driver v2.1 Nov 20 2009 22:08:08 Registered<242>
     
744. 
     
745. NBUFF v1.0 Initialized
     
746. 
     
747. Broadcom Packet Flow Cache learning via BLOG enabled.
     
748. 
     
749. Created Proc FS /procfs/fcache
     
750. 
     
751. Broadcom Packet Flow Cache registered with netdev chain
     
752. 
     
753. Constructed Broadcom Packet Flow Cache v2.1 Nov 20 2009 22:08:06
     
754. 
     
755. Broadcom Packet CMF (Experimental) Char Driver v0.1 Nov 20 2009 22:08:03 Registered<232>
     
756. 
     
757. Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Nov 20 2009 22:08:02 Loaded
     
758. 
     
759. bcmxtmcfg: bcmxtmcfg_init entry
     
760. 
     
761. adsl: adsl_init entry
     
762. 
     
763. Broadcom BCMPROCFS v1.0 initialized
     
764. 
     
765. Broadcom BCM6368B2 Ethernet Network Device v0.1 Oct 21 2011 08:03:17
     
766. 
     
767. KLOB extended to 2 pools
     
768. 
     
769. KLOB extended to 3 pools
     
770. 
     
771. KLOB extended to 4 pools
     
772. 
     
773. Config Switch Through SPI Slave Select 1
     
774. 
     
775. ethsw: found bcm53115!
     
776. 
     
777. dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
     
778. 
     
779. Broadcom Packet CMF (Experimental) SWC RESET.
     
780. 
     
781. Broadcom Packet CMF (Experimental) SWC INITIALIZED.
     
782. 
     
783. KLOB extended to 5 pools
     
784. 
     
785. KLOB extended to 6 pools
     
786. 
     
787. KLOB extended to 7 pools
     
788. 
     
789. KLOB extended to 8 pools
     
790. 
     
791. Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Nov 20 2009 22:08:03 Registered
     
792. 
     
793. Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Nov 20 2009 22:08:03 Registered
     
794. 
     
795. Broadcom Packet CMF (Experimental) ENABLED.
     
796. 
     
797. eth0: MAC Address: 20:4E:7F:0F:89:CF
     
798. 
     
799. eth1: MAC Address: 20:4E:7F:0F:89:CE
     
800. 
     
801. eth2: MAC Address: 20:4E:7F:0F:89:CE
     
802. 
     
803. eth3: MAC Address: 20:4E:7F:0F:89:CE
     
804. 
     
805. eth4: MAC Address: 20:4E:7F:0F:89:CE
     
806. 
     
807. eth0 Link DOWN.
     
808. 
     
809. eth1 Link DOWN.
     
810. 
     
811. eth2 Link DOWN.
     
812. 
     
813. eth3 Link DOWN.
     
814. 
     
815. eth4 Link DOWN.
     
816. 
     
817. PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
     
818. 
     
819. PCI: Setting latency timer of device 0000:00:01.0 to 64
     
820. 
     
821. wl0: Broadcom BCM4351 802.11 Wireless Controller 5.10.120.0.cpe4.404.8
     
822. 
     
823. dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
     
824. 
     
825. PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
     
826. 
     
827. PCI: Setting latency timer of device 0000:00:02.0 to 64
     
828. 
     
829. wl1: Broadcom BCM4350 802.11 Wireless Controller 5.10.120.0.cpe4.404.8
     
830. 
     
831. dgasp: kerSysRegisterDyingGaspHandler: wl1 registered
     
832. 
     
833. p8021ag: p8021ag_init entry
     
834. 
     
835. Broadcom Packet Flow Cache learning via BLOG disabled.
     
836. 
     
837. sh: cannot create /proc/sys/net/ipv4/neigh/br0/base_reachable_time: Directory nonexistent
     
838. Reading board data...
     
839. WSC UUID: 0x820e3bde0c80910537ba128a8728af81
     
840. wps_uuid=0x820e3bde0c80910537ba128a8728af81
     
841. klips_info:ipsec_init: KLIPS startup, Openswan KLIPS IPsec stack version: 2.4.9
     
842. 
     
843. NET: Registered protocol family 15
     
844. 
     
845. klips_info:ipsec_alg_init: KLIPS alg v=0.8.1-0 (EALG_MAX=255, AALG_MAX=251)
     
846. 
     
847. klips_info:ipsec_alg_init: calling ipsec_alg_static_init()
     
848. 
     
849. ipsec_3des_init(alg_type=15 alg_id=3 name=3des): ret=0
     
850. 
     
851. <6>KLIPS cryptoapi interface: alg_type=15 alg_id=12 name=cbc(aes) keyminbits=128 keymaxbits=256, found(0)
     
852. 
     
853. KLIPS: lookup for ciphername=cbc(twofish): not found
     
854. 
     
855. KLIPS: lookup for ciphername=cbc(serpent): not found
     
856. 
     
857. KLIPS: lookup for ciphername=cbc(cast5): not found
     
858. 
     
859. KLIPS: lookup for ciphername=cbc(blowfish): not found
     
860. 
     
861. <6>KLIPS cryptoapi interface: alg_type=15 alg_id=3 name=cbc(des3_ede) keyminbits=192 keymaxbits=192, found(0)
     
862. 
     
863. <6>KLIPS cryptoapi interface: alg_type=15 alg_id=2 name=cbc(des) keyminbits=64 keymaxbits=64, found(0)
     
864. 
     
865. ln: /dev/random: File exists
     
866. device eth1 entered promiscuous mode
     
867. 
     
868. device eth2 entered promiscuous mode
     
869. 
     
870. device eth3 entered promiscuous mode
     
871. 
     
872. device eth4 entered promiscuous mode
     
873. 
     
874. device wl0 entered promiscuous mode
     
875. 
     
876. eth1 Link UP 1000 mbps full duplex
     
877. 
     
878. device wl1 entered promiscuous mode
     
879. 
     
880. br0: port 6(wl1) entering learning state
     
881. 
     
882. br0: port 5(wl0) entering learning state
     
883. 
     
884. br0: port 1(eth1) entering learning state
     
885. 
     
886. sh: arping: not found
     
887. xtm command is xtm operate conn --createnetdev 1.8.35 atm0
     
888. bcmxtmrt: MAC address: 20 4e 7f 0f 89 d0
     
889. 
     
890. DSL mode command is xdslctl start --bitswap on --sra off --lpair i --mod dlt2pem --up
     
891. BcmAdsl_Initialize=0xC010EA10, g_pFnNotifyCallback=0xC0142FD4
     
892. 
     
893. Clocks for QPROC and AFE are being aligned with step through ...
     
894. 
     
895. AFE is aligned, i = 051, PhaseValue = -050, PhaseCntl = 0x3FCD0000
     
896. 
     
897. QPROC is aligned, i = 052, PhaseValue = -082, PhaseCntl = 0x3FCD7FCD
     
898. 
     
899. Clocks for QPROC and AFE are aligned with syn_status AFE = 0x70, QPROC = 0x70
     
900. 
     
901. AFE  phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f
     
902. 
     
903. QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f
     
904. 
     
905. pSdramPHY=0xA7FFFFF8, 0xFFFFFFFF 0xFFFFFFFF
     
906. 
     
907. *** XfaceOffset: 0x5FF90 => 0x5FF90 ***
     
908. 
     
909. br0: topology change detected, propagating
     
910. 
     
911. br0: port 6(wl1) entering forwarding state
     
912. 
     
913. br0: topology change detected, propagating
     
914. 
     
915. br0: port 5(wl0) entering forwarding state
     
916. 
     
917. br0: topology change detected, propagating
     
918. 
     
919. br0: port 1(eth1) entering forwarding state
     
920. 
     
921. *** PhySdramSize got adjusted: 0xC6F58 => 0xFD610 ***
     
922. 
     
923. AdslCoreSharedMemInit: shareMemAvailable=10704
     
924. 
     
925. AdslCoreHwReset:  pLocSbSta=872e0000 bkupThreshold=3072
     
926. 
     
927. AdslCoreHwReset:  AdslOemDataAddr = 0xA7FBC6D8
     
928. 
     
929. dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
     
930. 
     
931. DSL mode command is xdslctl configure --phycfg 0 0 0 0 0 0x00000002 0x00000000
     
932. info, udhcp server (v0.9.8) started
     
933. error, unable to parse 'option wins '
     
934. error, unable to parse 'option domain '
     
935. save_router_stats(721): port=4
     
936. POT integrity check OK.
     
937. POT time is up.
     
938. 192.168.0.1
     
939. c0a80001
     
940. automount: get SIGUSR1.
     
941. IOCTL_AG_REGION_SET: English
     
942. 
     
943. Info: No FWPT default policies.
     
944. killall: minidlna.exe: no process killed
     
945. httpd: socket bound in 0.0.0.0:80.
     
946. / # Virtual device wl0 asks to queue packet!
     
947. 
     
948. Setting SSID ""
     
949. Setting SSID "NETGEAR-2"
     
950. Setting SSID "NETGEAR-3"
     
951. Setting SSID "NETGEAR-4"
     
952. br0: port 5(wl0) entering disabled state
     
953. 
     
954. The kernel doesn't support the ebtables nat table.
     
955. The kernel doesn't support the ebtables nat table.
     
956. Couldn't open the directory
     
957. : No such file or directory
     
958. ftpRestart:
     
959. killall: bftpd: no process killed
     
960. killall: bftpd: no process killed
     
961. http_d: got signal
     
962. chanspec 0x2b01 selected
     
963. Setting SSID "NETGEAR"
     
964. device wl0 is already a member of a bridge; can't enslave it to bridge br0.
     
965. device wl0.1 entered promiscuous mode
     
966. 
     
967. device wl0.2 entered promiscuous mode
     
968. 
     
969. device wl0.3 entered promiscuous mode
     
970. 
     
971. br0: port 5(wl0) entering learning state
     
972. 
     
973. Reaped 1054
     
974. UPnP daemon is ready to run
     
975. br0: topology change detected, propagating
     
976. 
     
977. br0: port 5(wl0) entering forwarding state
     
978. 
     
979. Start WPS !!
     
980. Setting SSID "NETGEAR-5G"
     
981. Setting SSID "NETGEAR-5G-2"
     
982. Setting SSID "NETGEAR-5G-3"
     
983. Setting SSID "NETGEAR-5G-4"
     
984. br0: port 6(wl1) entering disabled state
     
985. 
     
986. Chanspec set to 0x1d26
     
987. The kernel doesn't support the ebtables nat table.
     
988. The kernel doesn't support the ebtables nat table.
     
989. The kernel doesn't support the ebtables nat table.
     
990. The kernel doesn't support the ebtables nat table.
     
991. The kernel doesn't support the ebtables nat table.
     
992. The kernel doesn't support the ebtables nat table.
     
993. The kernel doesn't support the ebtables nat table.
     
994. The kernel doesn't support the ebtables nat table.
     
995. The kernel doesn't support the ebtables nat table.
     
996. The kernel doesn't support the ebtables nat table.
     
997. device wl1 is already a member of a bridge; can't enslave it to bridge br0.
     
998. device wl1.1 entered promiscuous mode
     
999. 
     
1000. device wl1.2 entered promiscuous mode
      
1001. 
      
1002. device wl1.3 entered promiscuous mode
      
1003. 
      
1004. br0: port 6(wl1) entering learning state
      
1005. 
      
1006. Reaped 1375
      
1007. UPnP daemon is ready to run
      
1008. br0: topology change detected, propagating
      
1009. 
      
1010. br0: port 6(wl1) entering forwarding state
      
1011. 
      
1012. Start WPS !!
      
1013. 
      
1014. 
      
1015. 
      

复制代码